Welke terreinproeven uit te voeren? Basisonderzoek: sonderingen Boringen + monsterontname + ev peilbuizen Specifieke aanvullende proeven: DPT, FVT, DMT, PMT, SPT, PLT, SCPT Geofysische proeven
DMT apparatuur
In de grond brengen DMT sonde
DMT apparatuur
Onderzoek DMT: principe
proefuitvoering Membraan callibratie DMT sonde in de grond brengen Membraan onder druk brengen Juist tegen de grond aandrukken (uitbuiging 0.05mm) ; druk A Verder tegen de grond aandrukken (uitbuiging 1.1mm): druk B Eventueel druk verminderen tot opnieuw contact : druk C DMT sonde verder in de grond brengen (20cm) en procedure herhalen
Toepassings mogelijkheden Zand- klei- en leemgronden Niet voor grind DMT sonde kan in principe kracht van 250kN verdragen In praktijk druk beperkt tot 50MPa Kleien met c u 2-4 kpa tot 1000kPa
DMT apparatuur
proefresultaten Membraan callibratie DMT sonde in de grond brengen Membraan onder druk brengen Juist tegen de grond aandrukken (uitbuiging 0.05mm) ; druk A Verder tegen de grond aandrukken (uitbuiging 1.1mm): druk B Eventueel druk verminderen tot opnieuw contact : druk C DMT sonde verder in de grond brengen (20cm) en procedure herhalen Dissipatieproef: A-aflezingen ifv tijd Tijdstap verdubbelen
proefresultaten Membraan correctie, manometer nulpunt offset A-lezing: p 0 B-lezing: p 1 Berekeningen: intermediate DMT parameters Material index: I D = (p1 - p0) / (p0 - u0) Horizontal stressindex: K D = (p0 - u0) / σ'v0 Dilatometer modulus: E D = 34.7 (p1 - p0)
proefresultaten K 0 Coeff. Earth Pressure in Situ K 0,DMT = (K D / 1.5) 0.47-0.6 for I D < 1.2 OCR Overconsolidation Ratio OCR DMT = (0.5 K D ) 1.56 for I D < 1.2 c u Undrained Shear Strength c u,dmt = 0.22 σ' v0 (0.5 K D ) 1.25 for I D < 1.2 Φ Friction Angle Φ safe,dmt = 28 + 14.6 log K D - 2.1 log 2 K D for I D > 1.8 c h Coefficient of Consolidation c h,dmta 7 cm 2 / t flex t flex from A-log t DMT-A decay curve k h Coefficient of Permeability k h = c h γ w / M h (M h K 0 M DMT ) γ Unit Weight and Description (see chart in Fig. 16) M Vertical Drained Constrained Modulus M DMT = R M E D if I D 0.6 R M = 0.14 + 2.36 log K D if I D 3 R M = 0.5 + 2 log K D if 0.6 < I D < 3 R M = R M,0 + (2.5 - R M,0 ) log K D with R M,0 = 0.14 + 0.15 (I D - 0.6) if K D > 10 R M = 0.32 + 2.18 log K D if R M < 0.85 set R M = 0.85 u 0 Equilibrium Pore Pressure u 0 = p 2 = C - Z M + A In free-draining soils
Informatie uit DMT Grondsoort clay 0.1 < I D < 0.6 silt 0.6 < I D < 1.8 sand 1.8 < I D < (10) OCR Klei: OCR DMT = (0.5 KD) 1.56 Zand: M DMT /qc 5-10 NC 12-24 OC
Informatie uit DMT K 0 klei: K 0 = (K D / 1.5) 0.47-0.6 Zand: K 0 = 0.376 + 0.095 K D - 0.0017 qc /σ'v0 K 0 = 0.376 + 0.095 K D - 0.0046 qc /σ'v0
Informatie uit DMT c u c u = 0.22 σ' v0 (0.5 K D) 1.25 Φ φ safe,dmt = 28 + 14.6 log K D 2.1 log2 K D
Informatie uit DMT Constrained modulus M M DMT = R M E D R M = f(i D, K D ) c h from DMT-A dissipation D r, CBR, liquefaction potential, k h
DMT normen - referentiedocumenten ASTM D6635-01(2007) Standard Test Method for Performing the Flat Plate Dilatometer The Flat Dilatometer 5DMT) in soil investigations Report of the ISSMGE Technical Committee 16n Ground Property Characterisation from In-situ Testing 2001 ISSMGE EN 1997-2 Eurocode 7 - Geotechnical design - Part 2: Ground investigation and testing