UDC 677-66H:639.2.081.11 Visnetten - Snijden van geknoopt netwerk Fishing nets - Cutting knotted netting to shape ("tapering") NEN-ISO 1532 1e druk, mei 1976 Voor het snijden van geknoopt netwerk van visnetten is de internationale norm ISO 15З2, 1e druk, 1973, als Nederlandse norm aanvaard. Filets de pêche - Coupe de nappe de filet nouées Fishing nets - Cutting knotted netting to shape ("tapering") Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen. toestaan als een aanvullende licentieovereenkomst voor netwerkgebruik met NEN is afgesloten. This document may only be used on a stand-alone PC. Use in a network is only permitted when a supplementary license agreement for us in a network with NEN has been concluded. Voorbeeld Norme Internationale ISO 1532 Première édition 1973 Cette norme internationale a êtê acceptée intégralement comme norme néerlandaise. Beleidscommissie 330 "Textiel en kleding " International Standard ISO 1532 First edition 1973 This international standard has been completely accepted as a Netherlands standard. Niets uit deze norm mag worden verveelvoudigd en/of openbaar gemaakt door middel van druk, fotocopie, microfilm of op welke andere wijze ook, zonder voorafgaande schriftelijke toestemming van het NNI. Nederlands Normalisatie-instituut Polakweg 5, Rijswijk (ZH), telefoon (070) 90 68 00*, telex 32123, postrekening 25301 NEN-IS0 1532
Voorbeeld
Voorbeeld FOREWORD IS0 (the International Organization for Standardization) is a worldwide federation of national standards institutes (IS0 Member Bodies). The work of developing International Standards is carried out through IS0 Technical Committees. Every Member Body interested in a subject for which a Technical Committee has been set up has the right to be represented on that Committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the Technical Committees are circulated to the Member Bodies for approval before their acceptance as International Standards by the IS0 Council. Prior to 1972, the results of the work of the Technical Committees were published as IS0 Recommendations; these documents are now in the process of being transformed into International Standards. As part of this process, International Standard IS0 1532 replaces IS0 Recommendation R 1532-1970 drawn up by Technical Committee ISO/TC 38, Text/Yes. The Member Bodies of the following countries approved the Recommendation : Australia India Belgium Iran Brazil Israel Czechoslovakia Italy Denmark Japan Egypt, Arab Rep. of Netherlands France Norway Germany Peru Greece Poland Hungary Portugal Romania South Africa, Rep. of Spain Sweden Switzerland Turkey United Kingdom U.S.S.R. No Member Body expressed disapproval of the Recommendation. 0 International Organization for Standardization, 1973 l Printed in Switzerland
INTERNATIONAL STANDARD IS0 1532-1973 (E) Fishing nets - Cutting knotted netting to shape ( tapering ) 1 SCOPE AND FIELD OF APPLICATION This International Standard defines the different kinds of cutting knotted netting to shape by straight cut, the types of cutting (N-, T- and Bar-cut) and gives rules for the designation of the cutting rate. 4.1.1 N-cut (vertical cut) : A cut at right angles to the general course of the netting yarn just beyond the knots. N General course of the yarn 2 REFERENCE ISO 1107, Fishing nets - Netting - Basic terms and definitions. 1 ) 3 TERMINOLOGY The expression cutting knotted netting to shape is here understood to mean the cutting from knotted netting of pieces in the shape of trapezia, triangles, parallelograms or other polygons. FIGURE 1 CI z %.- 5 w.- ii 13 4 TYPES OF CUTTING Depending on the desired final shape of the netting, tapering cuts must be made in suitable ways, The various cutting rates are obtained by combining different lengths of cuts, either along a row of sequential knots (N- or T-cuts respectively) or parallel to a line of sequential mesh bars (B-cuts). See IS0 1107. The cuts along a row of sequential knots are distinguished by their situation in the drawing of the net or in the netting that has been hung up for tapering as described in 4.1.I and 4.1.2. 4.1 M-cuts (knot cuts) : Cuts just beyond the knots. K Voorbeeld 4.1.2 T-cut (horizontal cut) : A cut parallel to the general course of the netting yarn just beyond the knots. T General course of the yarn Direction of cut NOTE -- The term K-cut may be used instead of the two following terms in cases where the relation to the general course of the netting yarn is insignificant. FIGURE 2 1) At present at the stage of draft. (Revision of ISO/R 1107.)
Bestelformulier Stuur naar: NEN Standards Products & Services t.a.v. afdeling Klantenservice Antwoordnummer 10214 2600 WB Delft Ja, ik bestel NEN Standards Products & Services Postbus 5059 2600 GB Delft Vlinderweg 6 2623 AX Delft T (015) 2 690 390 F (015) 2 690 271 www.nen.nl/normshop ex. NEN-ISO 1532:1976 en Visnetten - Snijden van geknoopt netwerk 31.57 Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via www.nen.nl/normshop Gratis e-mailnieuwsbrieven Wilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen, normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze e-mailnieuwsbrieven. www.nen.nl/nieuwsbrieven Gegevens Bedrijf / Instelling T.a.v. O M O V E-mail Klantnummer NEN Uw ordernummer BTW nummer Postbus / Adres Postcode Plaats Telefoon Fax Factuuradres (indien dit afwijkt van bovenstaand adres) Postbus / Adres Postcode Plaats Datum Handtekening Retourneren Fax: (015) 2 690 271 E-mail: klantenservice@nen.nl Post: NEN Standards Products & Services, t.a.v. afdeling Klantenservice Antwoordnummer 10214, 2600 WB Delft (geen postzegel nodig). Voorwaarden De prijzen zijn geldig tot 31 december 2016, tenzij anders aangegeven. Alle prijzen zijn excl. btw, verzend- en handelingskosten en onder voorbehoud bij o.m. ISO- en IEC-normen. Bestelt u via de normshop een pdf, dan betaalt u geen handeling en verzendkosten. Meer informatie: telefoon (015) 2 690 391, dagelijks van 8.30 tot 17.00 uur. Wijzigingen en typefouten in teksten en prijsinformatie voorbehouden. U kunt onze algemene voorwaarden terugvinden op: www.nen.nl/leveringsvoorwaarden. Normalisatie: de wereld op één lijn. preview - 2016