Voorbeeld. Preview. Steel and steel products Inspection documents. Aciers et produits sidérurgiques Documents de contrôle. Second edition

Transcriptie

1 INTERNATIONAL STANDARD ISO Second edition Steel and steel products Inspection documents Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen. toestaan als een aanvullende licentieovereenkomst voor netwerkgebruik met NEN is afgesloten. This document may only be used on a stand-alone PC. Use in a network is only permitted when a supplementary license agreement for us in a network with NEN has been concluded. Aciers et produits sidérurgiques Documents de contrôle Reference number ISO 10474:2013(E) ISO 2013

2 ISO 10474:2013(E) COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO s member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel Fax copyright@iso.org Web Published in Switzerland ii ISO 2013 All rights reserved

3 ISO 10474:2013(E) Contents Page Foreword...iv 1 Scope Normative references Terms and definitions Inspection documents based on non-specific inspection Declaration of compliance with the order Test report Inspection documents based on specific inspection Inspection certificate Inspection certificate Inspection documents supplied by an intermediary Validation of inspection documents Summary of documents... 3 Bibliography... 4 ISO 2013 All rights reserved iii

4 ISO 10474:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. The committee responsible for this document is ISO/TC 17, Steel, Subcommittee SC 20, General technical delivery conditions, sampling and mechanical testing methods. This second edition cancels and replaces the first edition (ISO 10474:1991), which has been technically revised. iv ISO 2013 All rights reserved

5 Bestelformulier Stuur naar: NEN Standards Products & Services t.a.v. afdeling Klantenservice Antwoordnummer WB Delft Ja, ik bestel NEN Standards Products & Services Postbus GB Delft Vlinderweg AX Delft T (015) F (015) ex. ISO 10474:2013 en Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via Gratis nieuwsbrieven Wilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen, normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze nieuwsbrieven. Gegevens Bedrijf / Instelling T.a.v. O M O V Klantnummer NEN Uw ordernummer BTW nummer Postbus / Adres Postcode Plaats Telefoon Fax Factuuradres (indien dit afwijkt van bovenstaand adres) Postbus / Adres Postcode Plaats Datum Handtekening Retourneren Fax: (015) klantenservice@nen.nl Post: NEN Standards Products & Services, t.a.v. afdeling Klantenservice Antwoordnummer 10214, 2600 WB Delft (geen postzegel nodig). Voorwaarden De prijzen zijn geldig tot 31 december 2016, tenzij anders aangegeven. Alle prijzen zijn excl. btw, verzend- en handelingskosten en onder voorbehoud bij o.m. ISO- en IEC-normen. Bestelt u via de normshop een pdf, dan betaalt u geen handeling en verzendkosten. Meer informatie: telefoon (015) , dagelijks van 8.30 tot uur. Wijzigingen en typefouten in teksten en prijsinformatie voorbehouden. U kunt onze algemene voorwaarden terugvinden op: Normalisatie: de wereld op één lijn. preview