COMMERCIAL DOOR 1900 LIGHT-DUTY COMMERCIAL GRADE DOOR SERIES DBCI s Commercial Steel Curtain Roll-Up Door Solutions Include: 1900 Series (1950 Insulated) 26-gauge Grade E galvanized 2000 Series (2250 Insulated) 16-gauge galvanized steel drums with steel ball bearings 26-gauge Grade E steel curtain 2500 Series (2750 Insulated) Heavy duty 10-gauge steel slide bolt lock Width up to 18 feet 5000 Series (5250 Insulated) Aluminum bottom bar with steel angle reinforcement Wind certified up to 20 wide DBCI s 1900 Series is suitable for a number of lightduty commercial uses. These doors are easy to install and require low maintenance. You will enjoy steady, quiet operation. The 1900 Series utilizes 9 ½ drums instead of the standard 12 drum. This allows for less headroom when installing the doors. DBCI s commercial-grade steel curtain roll-up doors are designed to meet and/or exceed operational requirements for commercial doors with little or no maintenance. Integrity. Partnership. Quality.
Curtain 26-gauge galvanized, Grade E hard steel Deep-ribbed corrugation Maximum opening size of 12 x 14 Siliconized polyester WeatherX paint over prime coat 20 standard colors, special colors available upon request Wash coat over primer interior side 30-year film integrity warranty, up to 25-year chalk and fade warranty Flexible wear strips NOTE: The 1900 is not rated for wind loads. Please see the 2500 or 5000. Bottom Bar 6063 T6 aluminum extrusion 2 x 1 ½ galvanized angles Bulb astragal (Durometer 75) Stainless steel nuts and bolts Axle-Drum Assembly 1 5 /16 O.D. steel axle, 14-gauge 11-gauge on doors over 10 Oil-tempered torsion springs Utilizes 9 ½, 18-gauge drums Shielded steel ball bearings in drums 26-gauge full top sheet A.C.E. Guide System Advanced Curtain Engagement guide system Galvanized steel Adjustable bolt on head stop Polyethylene wear strip Pre-punched for lock and attachment fasteners Hardware 13-gauge saddle clamps 10-gauge slide locks; two per door 16-gauge step plate; two per door ¼ steel angle T-bracket Options Insulation 1950 Series Chain hoist 4:1 reduction Vision panels (17 x 5 ) Top draft stop Hood Steel mounting plates Opening Height Headroom Up to 10 is 17 of headroom 10 to 14 is 19 of headroom OPENING WIDTH + 18" 1.74 INTERIOR ELEVATION HEADROOM DETAIL DOOR OPENING 0.56 1.30 16 GA. 1.91 1.91 DOOR ENGAGEMENT STRIP SERIES 1900 MOUNTING INSULATED DOOR DETAIL FOIL BACKED AIR-BUBBLE INSULATION VINYL SIDE DRAFT STOP STRIP TAPCON XL STRIP STRIP WOOD STRIP MASONRY MOUNT STEEL MOUNT WOOD MOUNT SERIES 1950 DBCI Toll Free: 800.542.0501 E-mail: commercial@dbci.com * For more detailed information and drawings: www.dbci.com
COMMERCIAL DOOR 2000 LIGHT DUTY COMMERCIAL GRADE DOOR SERIES DBCI s Commercial Steel Curtain Roll-Up Door Solutions Include: 1900 Series (1950 Insulated) 26-gauge Grade E galvanized 2000 Series (2250 Insulated) 16-gauge galvanized steel drums with steel ball bearings 26-gauge Grade E steel curtain 2500 Series (2750 Insulated) Heavy duty 10-gauge steel slide bolt lock Width up to 18 feet 5000 Series (5250 Insulated) Aluminum bottom bar with steel angle reinforcement Wind certified up to 20 wide The 2000 Series is the right choice for light-duty applications requiring frequent usage such as warehouses, freight terminals, car washes, machine shops, auto body shops and much more. The 16-gauge, 12 drums allow for easy retraction. These doors are low-maintenance, which is what every owner wants in a quality door. DBCI s commercialgrade steel curtain roll-up doors are designed to meet and/or exceed operational requirements for commercial doors with little or no maintenance. Integrity. Partnership. Quality.
Curtain 26-gauge galvanized, Grade E hard steel Deep-ribbed corrugation Maximum opening size of 12 x 18 Flexible wear strips NOTE: The 2000 is not rated for wind loads. Please see the 2500 or 5000. Bottom Bar 6063 T6 aluminum extrusion 2 x 1 ½ galvanized angles Bulb astragal Stainless steel nuts and bolts Axle-Drum Assembly 1 5 16 O.D. steel axle, 14-gauge 11-gauge axle on doors over 10 wide Utilizes 12, 16-gauge drums Shielded steel ball bearings in drums Full top sheet Hardware Saddle clamps with set fasteners 10-gauge slide locks; 2 per door 16-gauge step plate; 2 per door ¼ steel angle T-bracket Opening Height Headroom Doors up to 10 have 20 of headroom Doors 10 to 14 have 22 of headroom Doors over 14 have 24 of headroom Options Insulated 2250 Series 1900 Series low overhead option Chain hoist 4:1 reduction Vision panels (17 x 5 ) Top draft stop Hood Steel mounting plates Electric operator A.C.E. Guide System 16-gauge galvanized steel Adjustable bolt on head stop Polyethylene wear strip Pre-punched for lock and attachment fasteners OPENING WIDTH + 18" 1.74 INTERIOR ELEVATION HEADROOM DETAIL DOOR OPENING 0.56 1.30 16 GA. 1.91 1.91 DOOR ENGAGEMENT STRIP SERIES 2000 MOUNTING INSULATED DOOR DETAIL FOIL BACKED AIR-BUBBLE INSULATION VINYL SIDE DRAFT STOP STRIP TAPCON XL STRIP STRIP WOOD STRIP MASONRY MOUNT STEEL MOUNT WOOD MOUNT SERIES 2250 DBCI Toll Free: 800.542.0501 E-mail: commercial@dbci.com * For more detailed information and drawings: www.dbci.com
COMMERCIAL DOOR 2500 HEAVY DUTY COMMERCIAL GRADE DOOR SERIES DBCI s Commercial Steel Curtain Roll-Up Door Solutions Include: 1900 Series (1950 Insulated) 26-gauge Grade E galvanized 2000 Series (2250 Insulated) 16-gauge galvanized steel drums with steel ball bearings 26-gauge Grade E steel curtain 2500 Series (2750 Insulated) Heavy duty 10-gauge steel slide bolt lock Width up to 18 feet 5000 Series (5250 Insulated) Aluminum bottom bar with steel angle reinforcement Wind certified up to 20 wide The 2500 Series is DBCI s heavy duty steel curtain roll-up door with tremendous versatility and unmatched quality. The 2500 Series has deep engagement guides creating greater durability and stronger, longer lasting performance. DBCI s commercial-grade steel curtain roll-up doors are designed to meet and/or exceed operational requirements for commercial doors with little or no maintenance. Integrity. Partnership. Quality.
Curtain 26-gauge galvanized, Grade E hard steel Deep-ribbed corrugation Maximum opening size of 18 x 18 Flexible wear strips NOTE: The 2500 Series are wind rated up to 12 0 wide and approximately 90 MPH. The MPH rating increases as the door width decreases. For test results on doors up to 12 0 wide, please contact DBCI Sales at 800.542.0501. Bottom Bar 6063 T6 aluminum extrusion 2 x 1 ½ galvanized angles Bulb astragal Stainless steel nuts and bolts Axle-Drum Assembly 1 5 16 O.D. steel axle, 14-gauge 11-gauge axle on doors over 10 wide Utilizes 12, 16-gauge drums Shielded steel ball bearings in drums Full top sheet Oil tempered torsion springs A.C.E. Guide System 14-gauge galvanized steel Adjustable bolt on head stop Polyethylene wear strip Pre-punched for lock and attachment fasteners Hardware Saddle clamps with set fasteners 10-gauge slide locks; 2 per door 16-gauge step plate; 2 per door ¼ steel welded angle T-bracket Opening Height Headroom Doors up to 10 have 20 of headroom Doors 10 to 14 have 22 of headroom Doors over 14 have 24 of headroom Options Insulated 2750 Series Chain hoist 4:1 reduction Vision panels (17 x 5 ) Top draft stop Hood Steel mounting plates Electric operator Low headroom 2400 Series INTERIOR ELEVATION OPENING WIDTH + 18" HEADROOM DETAIL 2.97 1.30 14 GA. 1.94 DOOR OPENING 0.57 3.16 DOOR ENGAGEMENT STRIP SERIES 2500 MOUNTING INSULATED DOOR DETAIL FOIL BACKED AIR-BUBBLE INSULATION VINYL SIDE DRAFT STOP STRIP TAPCON XL STRIP STRIP WOOD STRIP MASONRY MOUNT STEEL MOUNT WOOD MOUNT SERIES 2750 DBCI Toll Free: 800.542.0501 E-mail: commercial@dbci.com Website: www.dbci.com
COMMERCIAL DOOR 5000 WIND CERTIFIED DOOR SERIES DBCI s Commercial Steel Curtain Roll-Up Door Solutions Include: 1900 Series (1950 Insulated) 26-gauge Grade E galvanized 2000 Series (2250 Insulated) 16-gauge galvanized steel drums with steel ball bearings 26-gauge Grade E steel curtain 2500 Series (2750 Insulated) Heavy duty 10-gauge steel slide bolt lock Width up to 18 feet 5000 Series (5250 Insulated) Aluminum bottom bar with steel angle reinforcement Wind certified up to 20 wide When it comes to withstanding Mother Nature s wrath, DBCI has the doors you need. Our 5000 Series utilizes deep engagement guides and side curtain windlocks that are designed to maintain the operation integrity of the door and meet most state and local building codes, especially in coastal regions and Florida. The 5000 Series is made of 26-gauge, Grade E hard steel to ensure quality and dependability. DBCI s commercialgrade steel curtain roll-up doors are designed to meet and/or exceed operational requirements for commercial doors with little or no maintenance. Integrity. Partnership. Quality.
Fueled by constant changes in local and national building codes, as well as increasing insurance costs, doors with validated wind certification can dramatically reduce maintenance and replacement costs and minimize downtime. DBCI s wind-certified doors are designed to meet stringent building codes in coastal regions and Florida. Curtain 26-gauge galvanized, Grade E hard steel Deep-ribbed corrugation with three-rivet windlock attachment Maximum opening size of 20 x 16 Flexible wear strips NOTE: The 5000 Series are wind rated up to 20 0 wide and approximately 120 MPH. The MPH rating increases as the door width decreases. For test results on doors up to 20 0 wide, please contact DBCI Sales at 800.542.0501. Approximate* MPH Certification 10 wide = 150 mph 12 wide = 150 mph 14 wide = 146 mph 16 wide = 140 mph *For test results on doors up to 20 wide, please contact DBCI Commercial Sales at 800.542.0501. Bottom Bar 6063 T6 aluminum extrusion 2 x 1 ½ galvanized angles Bulb astragal Stainless steel nuts and bolts Axle-Drum Assembly 1 5 16 O.D. steel axle, 14-gauge 11-gauge axle on doors over 10 wide Utilizes 12, 16-gauge drums Shielded steel ball bearings in drums Full top sheet Oil tempered torsion springs A.C.E. Guide System 12-gauge galvanized steel 12-gauge wind lock bar Adjustable bolt on head stop Polyethylene wear strip Pre-punched for lock and attachment fasteners Hardware Saddle clamps with set fasteners 10-gauge slide locks; 2 per door 16-gauge step plate; 2 per door ¼ steel angle T-bracket Opening Height Headroom Doors up to 10 require 20 of headroom Doors 10 to 14 require 22 of headroom Doors over 14 require 24 of headroom Options Chain hoist 8:1 reduction Header seal Hood Steel mounting plates Electric operator *Also available with insulation (5250 Series) INTERIOR ELEVATION 10 1/2" BRACKET ATTACHMENT: CONCRETE/MASONRY: SLEEVE ANCHOR, 3/8" X 1-7/8" LG. WOOD: LAG, 3/8-7 X 3" LG. STEEL: HEX BOLT, GR.5, 3/8-24 X 1-1/4" LG. (*) FOR PUSH-UP OPERATION 6-1/2" FOR HAND CHAIN OR ELECTRIC OPERATION 10" NOTE: LEFT SIDE DRIVE SHOWN WALL OPENING WIDTH 10-1/2" DETAIL EXISTING STEEL JAMB 1/4" MIN. THICKNESS END OF AXLE TOP BARREL ASSEMBLY 6-1/2" END OF AXLE HEAD STOP (REMOVABLE) SYMMETRICAL TYPICAL PANEL CURTAIN WIND LOCK AT EVERY OTHER CORRUGATION MOUNTING UNIVERSAL CONCRETE/ MASONRY JAMBS BOTTOM BAR ASSEMBLY WOOD/ STEEL JAMBS 4" GRADE 3/8" SLIP FOR DOOR WIDTH LESS THAN OR EQUAL TO 12'-10"; 1/2" SLIP FOR DOOR WITH GREATER THAN 12'-10" AND LESS THAN 16'-10" EXISTING STEEL JAMB DOOR ENGAGEMENT TYPICAL PANEL TYPICAL PANEL 1/2" 1" MIN. WIND LOCK AT EVERY OTHER CORRUGATION WIND LOCK AT EVERY OTHER CORRUGATION MASONRY MOUNT STEEL MOUNT 800.635.3224 info@rollupdoorsonline.com www.rollupdoorsonline.com