ExDetector IRCO2 ExDetector IRHC Gas Detection and Warning Systems
Installation / Set-up In combination with a controller system, gas detectors in the ExDetector IR range haven the following functions: Measurement and display of the current concentration of gases and vapours Monitoring and warning of the presence of these gases Initiating protective measures: - Technical: countering a further increase in concentration (fans, switching off...) - Organisational: visual and acoustic messages and warnings. Detector Controler A gas warning system consists of the following components: Sensor Controller system Controllable devices such as fans, warning signs, and solenoid valves Product Features Exdetector IRCO2: detection of carbon dioxide CO 2 ExDetector Measurement range: 2.0 vol % Exdetector IRHC: Monitoring gases and vapours capable of forming an explosive mixture Measurement range: 0... 100 % LEL NDIR (non-dispersive infrared) Linear measurement signal 4... 20 ma One-man calibration (using optional calibrator) Certified for use in Ex-zones 1 and 2 Three-conductor technology - 24 VDC - 4... 20 ma - Neutral How It Works Light source Path of beam Gas inlet Measuring chamber Optical filter Detectors The NDIR sensor element consists of a light source, optical band filters, and detectors. The light source emits a pulsing, wide-band spectrum. The light beams pass through the measuring chamber, and the substance being monitored enters it by diffusion. Certain gases have the property of absorbing some radiation intensity in particular wave-length regions. At the end of the optical path, there are two detectors. Before radiation reaches them, it must pass through two optical band filters. Their transmission range is chosen to suit the detection task. The transmission range of the reference filter is limited to a wave-length range that is not absorbed by the gas to be detected. The filter of the detector only allows passage of the spectrum that can be absorbed by the gas. From the difference recorded between the detector and its compensation detector, the concentration of the gas is determined using linearisation algorithms. In addition, a temperature measurement compensates for ambient temperature effects. The detector electronics are supplied with 24VDC. They supply a linear, 4... 20 ma signal, proportional to the quantity being measured, for further evaluation. Using the optional calibrator, which is also explosion-protected, operating parameters can be programmed and the detector element adjusted. Thus, operation and maintenance can also be carried out in hazard zones. Page 2
Block Diagram "EEx e" "EEx d" 1 DC DC "EEx e" "EEx d" DC 2 U 4-20mA CPU # 3 # Interface U "EEx i" Technical Data General ExDetector IRCO2 31 Field of application Ex-zones 1 and 2 ExDetector IRHC 32 ExDetector IRHC 33 ExDetector IRHC 34 Equipment category Installation Detection gases Wall-mounting Carbon dioxide CO2 Combustible gases / vapours (see list "Technical Data, Substances) Measurement range: 0... 2.0 vol % 0... 100% LEL Measurement principle: Response time (T90) Max. flow speed NDIR (non-dispersive infrared) Depending on detection gas < 50 sec 6 m/sec Temperature range -20 C... +55 C Air pressure range 900... 1100 hpa Humidity range 30... 90 % RH Technical Data Substances Detectable substances: ExDetector IRHC 32: propane, n-pentane, n-hexane, nonane, methanol, ethanol, butanol, butyl acetate, methyl methacrylate, dioxane, methyl ethyl ketone (MEK) ExDetector IRHC 33: methane, benzene, toluene, xylene ExDetector IRHC 34: acetylene (ethyne) Page 3
Technical Data Installation Field interface Supply voltage (detector terminals) Calibration interface Safety-related maximum voltage Max. cable length 4... 20 ma 18... 32 VDC SELV / PELV max 5.5 W Fuse 100 mat Ex-classification: Ex ib IIC; only for connection to a certified intrinsically-safe circuit: Ui = 13.8 V / Pi = 432 mw / Li = 0 / Ci = 0 Um = 250 V 1000m depending on cable type Connection cable Suitable controller Explosion-protection Certificate Functional assessment 3 active conductors, screened, preferably H05VVC4V5-K Gasmesscomputer 8022, GMC 8022E, GMC 8364 Housing/electronics: Ex de [ib] IIC T6 PTB00ATEX1075-20 C < TA < +55 C Applied for Sensor head: Ex ed IIC T6 for -20 C < TA < 55 C PTB00ATEX1076U Mechanical Data Degree of protection (housing) Housing material Weight Cable gland IP54 Sensor: stainless steel Housing: aluminium ca. 1300 g Cable diameter 8... 13 mm Connection terminals 3 terminals 0.5... 1.5 mm 2 ExDetector 85 mm 170 mm 110 mm Page 4
Assessments Explosion-protection Certificates - Housing/electronics (): Ex de [ib] IIC T6 PTB 00 ATEX 1075 - Sensor: / Ex ed IIC T4 für -20 C < TA < +80 C T6 für -20 C < TA < +55 C PTB 00 ATEX 1076U Functional assessment: applied for Safety For its intended use in Ex-zones 1 and 2, the ExDetector, which complies with the following standards, ensures the highest levels of safety and reliability: EN 50270 (product standard) Electromagnetic compatibility of electrical equipment for the detection and measurement of combustible gases, toxic gases, oxygen and breath alcohol. Accessories Test-gas set Calibration gases Calibrator Calibrationbox-i Service Everything from a single supplier - from system design to installation of your new gas warning system. The comprehensive coverage of our sales and service network ensures this. Ask us about regional representatives in your area. And after purchase, our service technicians are available to help and advise. Page 5
Bieler + Lang GmbH Gas Detection and Warning Systems Postfach 1129, D-77842 Achern Von-Drais-Straße 31, D-77855 Achern Telephone +49 (0) 78 41 69 37-0 Telefax +49 (0) 78 41 69 37-99 E-mail info@bieler-lang.de Internet www.bieler-lang.de Technical status: 01/2011 We reserve the right to make technical changes! Page 6
EURO-INDEX Service Onderhoud en kalibratie van meetinstrumenten... EURO-INDEX beschikt over een bijzonder modern service- en kalibratielaboratorium. Hier worden de meetinstrumenten uit het assortiment preventief onderhouden, gerepareerd, gekalibreerd en indien nodig gejusteerd. Het service- en kalibratielaboratorium van EURO-INDEX is verdeeld in verschillende disciplines, gebaseerd op het soort meetinstrument en de gemeten grootheden. Druk Gasanalyse Temperatuur (inclusief infrarood temperatuurmeting en thermografie) Elektrische grootheden Gasdetectie Luchtsnelheid en luchthoeveelheid Waarom een kalibratiecertificaat?... Een kalibratiecertificaat vermeldt hoeveel een meetinstrument afwijkt ten opzichte van onze, naar (inter)nationale standaarden herleidbare, kalibratiemiddelen. Bij de meetresultaten op het certificaat wordt tevens vermeld of het meetinstrument voldoet aan de specificaties die door de fabrikant zijn opgegeven. Zonder kalibratiecertificaat kunt u er vanuit gaan dat de meter voldoet aan de fabrieksspecificaties, maar aantonen kunt u dit niet. Een testcertificaat van de fabrikant is te beknopt om de lineairiteit aan te tonen en is niet geregistreerd op naam (wat wel degelijk een vereiste is). SPECIMENEN SPECIMEN KWS... KWS is een uniek servicesysteem voor uw meetinstrumenten met periodiek onderhoud en kalibratie. Veel zaken worden voor u geregeld, zodat u zonder zorgen gebruik kunt maken van uw meetinstrumenten. De prijs staat vast voor de levensduur van het instrument (mits de KWS behandeling volgens herkalibratieadvies periodiek wordt uitgevoerd in het EURO-INDEX kalibratielaboratorium) Geen arbeidsloon bij de KWS behandeling Kalibratie voor justage (voorkalibratie) indien mogelijk Indien nodig justage en (na)kalibratie Reparatie en preventief onderhoud Gratis oproep met het advies voor herkalibratie Controle op functionaliteit van het instrument Vijf jaar historie voor alle gegevens 10% korting op onderdelen Serienummerregistratie Franco retourlevering RvA accreditatie... Het kalibratielaboratorium van EURO-INDEX beschikt sinds 21 augustus 1997 over een RvA accreditatie naar NEN-EN-ISO/IEC 17025. Deze accreditatie geldt voor verschillende grootheden, zoals gespecificeerd in de scope bij accreditatienummer K105 op www.rva.nl. Test- en meetinstrumenten voor grootheden die deel uitmaken van de gespecificeerde scope, kunnen worden voorzien van een RvA kalibratiecertificaat. De metingen worden uitgevoerd met standaarden waarvan de herleidbaarheid naar (inter)nationale standaarden, ten overstaan van de Raad voor Accreditatie, is aangetoond. In het Multilateral Agreement zijn de meeste Europese landen overeengekomen elkaars accreditaties te accepteren. Hierdoor is een RvA kalibratiecertificaat internationaal geaccepteerd. Bovendien wordt op een RvA kalibratiecertificaat de meetonzekerheid van de gerapporteerde meetresultaten vermeld. Verhuur van meetinstrumenten... EURO-INDEX biedt een assortiment meetinstrumenten te huur aan. Na deskundig advies van onze productspecialisten, wordt bepaald welk instrument u nodig heeft voor uw specifieke werkzaamheden. De instrumenten worden compleet met accessoires geleverd, inclusief herleidbaar kalibratiecertificaat. Wijzigingen voorbehouden EURO-INDEX NL 13002 NEDERLAND Rivium 2e straat 12 2909 LG Capelle a/d IJssel T: 010-2 888 000 F: 010-2 888 010 www.euro-index.nl verkoop@euro-index.nl Leuvensesteenweg 607 BELGIË 1930 Zaventem T: +32 - (0)2-757 92 44 F: +32 - (0)2-757 92 64 www.euro-index.be verkoop@euro-index.be