Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen. toestaan als een aanvullende licentieovereenkomst voor netwerkgebruik met NEN is afgesloten. This document may only be used on a stand-alone PC. Use in a network is only permitted when a supplementary license agreement for us in a network with NEN has been concluded. Nederlandse norm NEN-EN-IEC 61158-2 (en) Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition (IEC 61158-2:2007,IDT) Vervangt NEN-EN-IEC 61158-2:2004,deels; NEN-EN-IEC 61491:1998,deels
NEN-EN-IEC 61158-2 Als Nederlandse norm is aanvaard: - EN 61158-2:2008,IDT - IEC 61158-2:2007,IDT Nederlands Elektrotechnisch Comité (NEC) Normcommissie Industriele meet"en regeltechniek (NEC 65)" Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by means of photocopy, microfilm, storage in computer files or otherwise, which also applies to full or partial processing, without the written consent of the Netherlands Standardization Institute. The Netherlands Standardization Institute shall, with the exclusion of any other beneficiary, collect payments owed by third parties for duplication and/or act in and out of law, where this authority is not transferred or falls by right to the Reproduction Rights Foundation. Auteursrecht voorbehouden. Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking. Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht. Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. The Netherlands Standardization Institute and/or the members of the committees therefore accept no liability, not even for direct or indirect damage, occurring due to or in relation with the application of publications issued by the Netherlands Standardization Institute. Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdend met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven. 2008 Nederlands Normalisatie-instituut Postbus 5059, 2600 GB Delft Telefoon (015) 2 690 390, Fax (015) 2 690 190
NEN-EN-IEC 61158-2 Nederlands voorwoord Voor de in deze norm vermelde normatieve verwijzingen bestaan in Nederland de volgende equivalenten: vermelde norm Nederlandse norm titel IEC 60050-731 NEN 10050-731 Internationale Elektrotechnische Woordenlijst - Hoofdstuk 731: Glasvezelcommunicatie (en,fr,ru,es) IEC 60079-11 NEN-EN-IEC 60079-11 Explosieve atmosferen - Deel 11: Bescherming van materieel door intrinsieke veiligheid "i" (en,fr) IEC 60079-14 NEN-EN-IEC 60079-14 Elektrisch materieel voor plaatsen waar gasontploffingsgevaar kan heersen - Deel 14: Elektrische installaties in gevaarlijke gebieden (anders dan in mijnen) (en,fr,nl) IEC 60079-25 NEN-EN-IEC 60079-25 Elektrisch materieel voor plaatsen waar gasontploffingsgevaar kan heersen - Deel 25: Intrinsiek-veilige systemen (en,fr) IEC 60096-1 NEN 10096-1 Hoogfrequentiekabels - Deel 1: Algemene eisen en meetmethoden (en,fr) IEC 60169-8 IEC 60169-17 NEN 10169-17 Hoogfrequentieconnectors - Deel 17: Coaxiaalconnectors met een binnenmiddellijn van de buitengeleider van 6,5 mm met schroefkoppeling - Karakteristieke impedantie 50 ohm (Type TNC) (en,fr) IEC 60189-1:1986 IEC 60255-22-1:1988 IEC 60364-4-41 HD 60364-4-41 Elektrische laagspanningsinstallaties - Deel 4-41: Beschermingsmaatregelen - Bescherming tegen elektrische schok (en,fr) IEC 60364-5-54 HD 60364-5-54 Elektrische installaties van gebouwen - Deel 5-54: Keuze en installatie van elektrisch materieel - Aardingsvoorzieningen, beschermings- en vereffeningsleidingen (en) IEC 60529 NEN 10529 Beschermingsgraden van omhulsels van elektrisch materieel (IP-codering) (en,fr) IEC 60603-7 NEN 10603-7 Connectors voor panelen met gedrukte bedrading en gebruik bij frequenties beneden 3 MHz - Deel 7: Raamspecificatie voor 8-polige paneelconnectors en de bijbehorende kabelconnectors, van vastgestelde kwaliteit (en,fr) IEC 60760 NEN 10760 Vlakstekers (en,fr) IEC 60793:series NEN-EN-IEC 60793:reeks Optical fibres (en) IEC 60794-1-2 NEN-EN-IEC 60794-1-2 Optische vezelkabels - Deel 1-2: Hoofdspecificatie - Basisbeproevingsprocedures voor optische kabels (en,fr) IEC 60807-3 NEN 10807-3 Rechthoekige connectors voor gebruik bij frequenties beneden 3 MHz - Deel 3: Artikelspecificatie voor een reeks van connectors met trapeziumvormige metalen behuizing en cylindrische contacten - Uitneembare krimpcontacten met gesloten krimpaansluitingen, vanaf de achterzijde verwisselbaar (en,fr) IEC 60874-10-1 IEC 61000-4-2 NEN 11000-4-2 Elektromagnetische compatibiliteit (EMC) - Deel 4: Beproevingen en meettechnieken - Sectie 2: Elektrostatische ontlading - Immuniteitsproef - Algemene EMC-publicatie (en,fr) IEC 61000-4-3 NEN-EN-IEC 61000-4-3 Elektromagnetische compatibiliteit (EMC) - Deel 4-3: Beproevingen en meettechnieken - Uitgestraalde, radiofrequente, elektromagnetische velden - Immuniteitsproef (en)
NEN-EN-IEC 61158-2 IEC 61000-4-4 NEN-EN-IEC 61000-4-4 Elektromagnetische compatibiliteit (EMC) - Deel 4-4: Beproevingen en meettechnieken - Snelle elektrische transiënten en lawines - Immuniteitsproef (en,fr) IEC 61131-2 NEN-EN-IEC 61131-2 Programmeerbare besturingen - Deel 2: Apparatuur-eisen en beproevingen (en) IEC 61156-1 NEN-IEC 61156-1 Multicore and symmetrical pair/quad cables for digital communications - Part 1: Generic specification (en,fr) IEC 61158-4-2 NEN-EN-IEC 61158-4-2 Industriële communicatienetwerken - Veldbus specificaties - Deel 4-2: Protocolspecificatie van de gegevensverbindingslaag - Type 2 elementen (en) IEC 61158-4-3 NEN-EN-IEC 61158-4-3 Industriële communicatienetwerken - Veldbus specificaties - Deel 4-3: Protocolspecificatie van de gegevensverbindingslaag - Type 3 elementen (en) IEC 61754-2 NEN 11754-2 Optische-vezel connectorverbindingen - Deel 2: Connectorfamilie type BFOC/2,5 (en,fr) IEC 61754-13 NEN-EN-IEC 61754-13 Fibre optic connector interfaces - Part 13: Type FC- PC connector (en,fr) IEC 61754-22 NEN-EN-IEC 61754-22 Fibre optic connector interfaces - Part 22: Type F- SMA connector family (en,fr) ISO/IEC 7498:series NEN-EN-ISO/IEC 7498:reeks Informatietechnologie (en) ISO/IEC 8482 ISO/IEC 8802-3 NEN-ISO/IEC 8802-3 Informatietechnologie - Telecommunicatie en informatie-uitwisseling tussen systemen - Lokale en stedelijke netwerken - Specifieke eisen - Deel 3: Carrier sense multiple access met waarneming van botsingen (CSMA/CD) toegangsmethode en specificatie van de fysieke laag (en) ISO/IEC 9314-1 ISO/IEC 10731
EUROPEAN STANDARD EN 61158-2 NORME EUROPÉENNE EUROPÄISCHE NORM February 2008 ICS 25.040; 35.100; 35.240.50 Supersedes EN 61158-2:2004 and partially supersedes EN 61491:1998 English version Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition (IEC 61158-2:2007) Réseaux de communication industriels - Spécifications des bus de terrain - Partie 2: Spécification des couches physiques et définition des services (CEI 61158-2:2007) Industrielle Kommunikationsnetze - Feldbusse - Teil 2: Spezifikation und Dienstfestlegungen des Physical Layer (Bitübertragungsschicht) (IEC 61158-2:2007) This European Standard was approved by CENELEC on 2008-02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61158-2:2008 E
EN 61158-2:2008-2 - Foreword The text of document 65C/472/FDIS, future edition 4 of IEC 61158-2, prepared by SC 65C, Industrial networks, of IEC TC 65, Industrial-process measurement, control and automation, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61158-2 on 2008-02-01. This European Standard supersedes EN 61158-2:2004. Together with its companion parts for Type 16, it also partially replaces EN 61491:1998 which is at present being revised (to be issued as a Technical Report). With respect to EN 61158-2:2004 the following changes were made: deletion of Type 6 fieldbus for lack of market relevance; addition of new fieldbus types; generalization of the seldom-used Type 1 radio to a more useful form. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2008-11-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-02-01 NOTE Use of some of the associated protocol types is restricted by their intellectual-property-right holders. In all cases, the commitment to limited release of intellectual-property-rights made by the holders of those rights permits a particular data-link layer protocol type to be used with physical layer and application layer protocols in type combinations as specified explicitly in the EN 61784 series. Use of the various protocol types in other combinations may require permission of their respective intellectual-property-right holders. IEC and CENELEC draw attention to the fact that it is claimed that compliance with this standard may involve the use of patents as follows, where the [xx] notation indicates the holder of the patent right: Type 2 (Subclauses 5.3, 9.3, 10.3, Clauses 17 through 20, Annex F through Annex H): 5,396,197 [AB] Network Node TAP IEC and CENELEC take no position concerning the evidence, validity and scope of these patent rights. The holders of these patent rights have assured IEC that they are willing to negotiate licences under reasonable and nondiscriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holders of these patent rights are registered with IEC. Information may be obtained from: [AB]: Rockwell Technologies, LLC Allen-Bradley Co, LLC 1201 So. Second Street Milwaukee, WI 53204 USA Attention: Intellectual Property Dept. Attention is drawn to the possibility that some of the elements of this standard may be the subject of patent rights other than those identified above. IEC and CENELEC shall not be held responsible for identifying any or all such patent rights. Annex ZA has been added by CENELEC.
- 3 - EN 61158-2:2008 Endorsement notice The text of the International Standard IEC 61158-2:2007 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60079-0 NOTE Harmonized as EN 60079-0:2006 (modified). IEC 60079-27 NOTE Harmonized as EN 60079-27:2006 (not modified). IEC 60227-5 NOTE Harmonized as HD 21.5 S3:1994 (modified). IEC 60875-1 NOTE Harmonized as EN 60875-1:2001 (not modified). IEC 60947-5-2 NOTE Harmonized as EN 60947-5-2:2007 (not modified). IEC 61300-3-4 NOTE Harmonized as EN 61300-3-4:2001 (not modified). IEC 61491 NOTE Harmonized as EN 61491:1998 (modified). IEC 61596 NOTE Harmonized as EN 61596:1997 (not modified). IEC 61784-1 NOTE Harmonized as EN 61784-1:2008 (not modified).
EN 61158-2:2008-4 - Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60050-731 - 1) International Electrotechnical Vocabulary (IEV) - Chapter 731: Optical fibre communication IEC 60079-11 - 1) Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" IEC 60079-14 - 1) Explosive atmospheres - Part 14: Electrical installations design, selection and erection IEC 60079-25 - 1) Electrical apparatus for explosive gas atmospheres - Part 25: Intrinsically safe systems IEC 60096-1 - 1) Radio-frequency cables - Part 1: General requirements and measuring methods EN 60079-11 2007 2) EN 60079-14 2003 2) EN 60079-25 + corr. April IEC 60169-8 - 1) 3) Radio-frequency connectors - Part 8: R.F. coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with bayonet lock - Characteristic impedance 50 ohms (Type BNC) IEC 60169-17 - 1) Radio-frequency connectors - Part 17: R.F. coaxial connectors with inner diameter of outer conductor 6,5mm (0,256 in) with screw coupling - Characteristic impedance 50 ohms (type TNC) IEC 60189-1 1986 Low-frequency cables and wires with PVC insulation and PVC sheath - Part 1: General test and measuring methods 2004 2) 2006 1) Undated reference. 2) Valid edition at date of issue. 3) IEC 60169-8:1986 is superseded by IEC 61169-8:2007, which is harmonized as EN 61169-8:2007.
- 5 - EN 61158-2:2008 Publication Year Title EN/HD Year IEC 60255-22-1 1988 Electrical relays - Part 22-1: Electrical disturbance tests for measuring relays and protection equipment - 1 MHz burst disturbance tests - 4) - IEC 60364-4-41 (mod) IEC 60364-5-54 (mod) - 1) Low-voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock - 1) Electrical installations of buildings - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements, protective conductors and protective bonding conductors IEC 60529-1) Degrees of protection provided by enclosures (IP Code) IEC 60603-7 - 1) Connectors for frequencies below 3 MHz for use with printed boards - Part 7: Detail specification for connectors, 8-way, including fixed and free connectors with common mating features, with assessed quality HD 60364-4-41 + corr. July 2007 2) 2007 HD 60364-5-54 2007 2) EN 60529 + corr. May 1991 2) 1993 EN 60603-7 1997 2) IEC 60760-1) Flat, quick-connect terminations IEC 60793 (mod) Series Optical fibres EN 60793 Series IEC 60794-1-2-1) Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures EN 60794-1-2 2003 2) IEC 60807-3 - 1) Rectangular connectors for frequencies below 3 MHz - Part 3: Detail specification for a range of connectors with trapezoidal shaped metal shells and round contacts - Removable crimp types with closed crimp barrels, rear insertion/rear extraction IEC 60874-10-1-1) Connectors for optical fibres and cables - Part 10-1: Detail specification for fibre optic connector type BFOC/2,5 terminated to multimode fibre type A1 IEC 61000-4-2-1) Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test EN 61000-4-2 1995 2) IEC 61000-4-3-1) Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test EN 61000-4-3 2006 2) 4) EN 60255-22-1:2008 is based on IEC 60255-22-1:2007.
EN 61158-2:2008-6 - Publication Year Title EN/HD Year IEC 61000-4-4-1) Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test EN 61000-4-4 2004 2) IEC 61131-2 - 1) Programmable controllers - Part 2: Equipment requirements and tests IEC 61156-1 - 1) Multicore and symmetrical pair/quad cables for digital communications - Part 1: Generic specification EN 61131-2 2007 2) IEC 61158-4-2-1) Industrial communication networks - Fieldbus EN 61158-4-2 2008 2) specifications - Part 4-2: Data-link layer protocol specification - Type 2 elements IEC 61158-4-3-1) Industrial communication networks - Fieldbus EN 61158-4-3 2008 2) specifications - Part 4-3: Data-link layer protocol specification - Type 3 elements IEC 61754-2 - 1) Fibre optic connector interfaces - Part 2: Type BFOC/2,5 connector family IEC 61754-13 - 1) Fibre optic connector interfaces - Part 13: Type FC-PC connector IEC 61754-22 - 1) Fibre optic connector interfaces - Part 22: Type F-SMA connector family ISO/IEC 7498 EN 61754-2 1997 2) EN 61754-13 2006 2) EN 61754-22 2005 2) Series Information technology - Open systems EN ISO/IEC 7498 interconnection - Basic Reference Model: The Basic Model ISO/IEC 8482-1) Information technology - Telecommunications and information exchange between systems - Twisted pair multipoint interconnections ISO/IEC 8802-3 - 1) Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications ISO/IEC 9314-1 - 1) Information Processing Systems - Fibre distributed data interface (FDDI) - Part 1: Token Ring physical layer protocol (PHY) Series EN 29314-1 1993 2) ISO/IEC 10731-1) Information technology - Open Systems Interconnection - Basic reference model - Conventions for the definition of OSI services ANSI TIA/EIA-232-F - 1) ANSI TIA/EIA-422-B - 1) Interface between data terminal equipment and data circuit - Terminating equipment employing serial binary data interchange Electrical characteristics of balanced voltage digital interface circuits
- 7 - EN 61158-2:2008 Publication Year Title EN/HD Year ANSI TIA/EIA-485-A - 1) Electrical characteristics of generators and receivers for use in balanced digital multipoint systems ANSI TIA/EIA-644-A - 1) Electrical Characteristics of Low Voltage Differential Signaling (LVDS) Interface Circuits
INTERNATIONAL STANDARD IEC 61158-2 Edition 4.0 2007-12 Industrial communication networks Fieldbus specifications Part 2: Physical layer specification and service definition IEC 61158-2:2007(E)
THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varembé CH-1211 Geneva 20 Switzerland Email: inmail@iec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee, ). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csc@iec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00
INTERNATIONAL STANDARD IEC 61158-2 Edition 4.0 2007-12 Industrial communication networks Fieldbus specifications Part 2: Physical layer specification and service definition INTERNATIONAL ELECTROTECHNICAL COMMISSION PRICE CODE XP ICS 25.040; 35.100; 35.240.50 ISBN 2-8318-9447-6
ALTIJD DE ACTUELE NORM IN UW BEZIT HEBBEN? Nooit meer zoeken in de systemen en uzelf de vraag stellen: â Is en de laatste versie?â Via het digitale platform NEN Connect heeft u altijd toegang tot de meest actuele versie van deze norm. Vervallen versies blijven ook beschikbaar. U en uw collega s kunnen de norm via NEN Connect makkelijk raadplagen, online en offline. Kies voor slimmer werken en bekijk onze mogelijkheden op www.nenconnect.nl. Heeft u vragen? Onze Klantenservice is bereikbaar maandag tot en met vrijdag, van 8.30 tot 17.00 uur. Telefoon: 015 2 690 391 E-mail: klantenservice@nen.nl WERK SLIMMER MET NEN CONNECT