Voorbeeld. Preview. 2e Ontwerp. Publicatie uitsluitend voor commentaar. Commentaar voor Nederlandse

Transcriptie

1 Nederlandse 2e Ontwerp norm NEN-EN Kunststofleidingsystemen - Onder- en bovengrondsystemen voor water en andere vloeistoffen onder druk - Prestatiekenmerken voor buizen, hulpstukken en hun verbindingen Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes fittings and their joints Publicatie uitsluitend voor commentaar Commentaar voor Vervangt NEN-EN 15014:2004 Ontw. april 2007 ICS Als Europees normontwerp is gepubliceerd: pren 15014:2007,IDT Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen. toestaan als een aanvullende licentieovereenkomst voor netwerkgebruik met NEN is afgesloten. This document may only be used on a stand-alone PC. Use in a network is only permitted when a supplementary license agreement for us in a network with NEN has been concluded. Definitief vastgestelde normen zullen als Nederlandse norm gelden. Daarom wordt dit normontwerp in Nederland voor commentaar gepubliceerd. Op het ontwerp ingebracht commentaar zal aan de bevoegde normcommissie worden voorgelegd die hiermee rekening zal houden bij de bepaling van de Nederlandse stem. Indien er geen bezwaar bij NEN wordt ingebracht, kan dat leiden tot ongewijzigd definitieve vaststelling van het ontwerp als norm. Van Europese normen bestaan drie officiële versies: Engels, Frans en Duits. Voor Nederland zal de Engelse versie gelden, tenzij voor een geautoriseerde versie in het Nederlands wordt gekozen. Normcommissie "Kunststofleidingsystemen" Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by means of photocopy, microfilm, storage in computer files or otherwise, which also applies to full or partial processing, without the written consent of the Netherlands Standardization Institute. The Netherlands Standardization Institute shall, with the exclusion of any other beneficiary, collect payments owed by third parties for duplication and/or act in and out of law, where this authority is not transferred or falls by right to the Reproduction Rights Foundation. Auteursrecht voorbehouden. Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking. Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht. Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. The Netherlands Standardization Institute and/or the members of the committees therefore accept no liability, not even for direct or indirect damage, occurring due to or in relation with the application of publications issued by the Netherlands Standardization Institute. Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdend met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven Nederlands Normalisatie-instituut Postbus 5059, 2600 GB Delft Telefoon (015) , Fax (015)

2

3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM FINAL DRAFT pren March 2007 ICS English Version Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints Systèmes de canalisations en plastique - Systèmes enterrées et aériens pour eau et autres fluides avec pression - Caractéristiques de performance pour tubes, raccords et leurs assemblages Kunststoff-Rohrleitungssysteme - Erd- und oberirdisch verlegte Druckrohrleitungssysteme für Wasser und andere Flüssigkeiten - Eigenschaften für die Gebrauchstauglichkeit von Rohren, Formstücken und deren Verbindungen This draft European Standard is submitted to CEN members for second unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 155. If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. pren 15014:2007: E

4 Contents Foreword Scope Normative references Terms, definitions and symbols Performance requirements Reaction to fire External pressure strength Internal pressure strength Dimensional tolerances Tightness (air and liquid) Durability Dangerous substances Calculation and test methods Reaction to fire Determination of the nominal pressure Internal pressure strength Dimensional tolerances Tightness Durability Evaluation of conformity General Initial type testing Factory production control One-off products and products produced in very low quantities Annex A (normative) Product standards for buried and above-ground pressure piping systems in plastics materials for water for general purposes, drainage, sewerage, irrigation and other fluids Annex B (normative) Standards for assessment of conformity for buried and above-ground pressure piping systems in plastics materials for water for general purposes, drainage, sewerage, irrigation and other fluids Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Directive ZA.1 Scope and relevant characteristics ZA.2 Procedure for attestation of conformity of plastics pipes and fittings ZA.2.1 Systems of attestation of conformity ZA.2.2 EC Certificate and Declaration of conformity ZA.3 CE marking and labelling ZA.3.1 CE marking requirements ZA.3.2 Simplified CE marking with reference to a web site ZA General ZA Minimum rules for the proper use of a web site for CE marking information Bibliography Page 2

5 Foreword This document (pren 15014:2007) has been prepared by Technical Committee CEN/TC 155 Plastics piping systems and ducting systems, the secretariat of which is held by NEN. This document is currently submitted to the second Unique Acceptance Procedure. This document has been prepared under the mandate M/131 "Pipes, tanks and ancillaries not in contact with water intended for human consumption" given to CEN by the European Commission and the European Free Trade Association and support essential requirements of EU Directives. For the relationship with EU Directives, see informative Annex ZA, which is an integral part of this document. 3

6 Introduction This European Standard contains only the performance characteristics needed to meet the essential requirements of EU Directive(s). It does not cover all characteristics of the products. These are specified in the standards listed in Annex A or in other appropriate product specifications. For valves This harmonised European Standard is part of a family of cluster standards addressing plastics piping systems. The relationship is shown below. Material independent Specific solutions For the harmonisation of pressure plastics piping systems (this European Standard) the following applies: For pipes and fittings 4

7 1 Scope This European Standard specifies performance requirements for plastics pipes, fittings and their joints for buried or above-ground pressure applications for water for general purposes, drainage, sewerage and irrigation, as well as for any other pressure application with other fluids covered by the Construction Products Directive with the exception of drinking water distribution for human consumption. It gives associated test methods for verification and evaluation of conformity with this European Standard. NOTE Compliance of pipes, fittings and their joints with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC. However, until the operation of the envisaged European Acceptance Scheme for construction products in contact with water intended for human consumption and the revision of the present standard, products complying with the present standard could be used for the transport of water intended for human consumption if they comply with the relevant national, regional or local regulatory provisions applicable in the place of use. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN 681-4, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 4: Cast polyurethane sealing elements EN 713, Plastics piping systems Mechanical joints between fittings and polyolefin pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending EN 715, Thermoplastics piping systems End-load bearing joints between small diameter pressure pipes and fittings Test method for leaktightness under internal water pressure, including end thrust EN 911, Plastics piping systems Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping Test method for leaktightness under external hydrostatic pressure EN , Plastics piping systems for water supply Unplasticized poly(vinyl chloride) (PVC-U) Part 2: Pipes EN 1394, Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the apparent initial circumferential tensile strength EN 1778, Characteristic values for welded thermoplastic constructions Determination of allowable stresses and moduli for design of thermoplastic equipment EN 1796, Plastics piping systems for water supply with or without pressure Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) EN , Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fire tests 5

8 EN 14364, Plastics piping systems for drainage and sewerage with or without pressure Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) Specifications for pipes, fittings and joints pren 15012:2007, Plastics piping systems Soil and waste discharge systems within the building structure Performance characteristics for pipes, fittings and their joints EN ISO , Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method (ISO :2006) EN ISO , Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces (ISO :2006) pren ISO :2005, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components (ISO/DIS :2005) pren ISO :2006, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies (ISO/DIS :2006) EN ISO 3126, Plastics piping systems Plastics components Determination of dimensions (ISO 3126:2005) EN ISO 9001:2000, Quality management systems Requirements (ISO 9001:2000) EN ISO 9080, Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics material in pipe form by extrapolation (ISO 9080:2003) EN ISO 12162, Thermoplastics materials for pipes and fittings for pressure applications Classification and designation Overall service (design) coefficient (ISO 12162:1995) EN ISO 13783, Plastics piping systems Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double socket joints Test method for leaktightness and strength while subjected to bending and internal pressure (ISO 13783:1997) EN ISO 13846, Plastics piping systems End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping Test method for long-term leaktightness under internal water pressure (ISO 13846:2000) ISO 161-1, Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series ISO 13761, Plastics pipes and fittings Pressure reduction factors for polyethylene pipeline systems for use at temperature above 20 C ISO 17456, Plastics piping systems Multilayer pipes Determination of the long term hydrostatic strength ISO 21004, Plastics piping systems Multilayer pipes and their joints, based on thermoplastics, for water supply 6

9 3 Terms, definitions and symbols For the purposes of this document, the following terms, definitions and symbols apply. 3.1 nominal size (DN) numerical designation of the size of a component, other than a component designated by thread size, which is a convenient round number approximately equal to the manufacturing dimension in millimetres (mm). This can apply to either the internal diameter (DN/ID) or external diameter (DN/OD) 3.2 nominal outside diameter d n specified diameter, in millimetres, assigned to a nominal size 3.3 nominal pressure (PN) numerical designation used for reference purposes related to the mechanical characteristics of the component of a piping system NOTE For plastic piping systems conveying water it corresponds to the maximum continuous operating pressure in bar, which can be sustained with water at 20 C for thermoplastics and 35 C for thermosetting materials, based on the minimum design coefficient. 4 Performance requirements 4.1 Reaction to fire for applications inside building Where subject to regulatory requirements, the product shall be tested and classified in accordance with External pressure strength The external pressure strength of pressure piping systems is deemed to be satisfied by the internal pressure strength as given in Internal pressure strength Determination of nominal pressure PN For thermoplastics materials the internal pressure strength of the pipe and fitting shall be determined in accordance with and shall be declared by the manufacturer as nominal pressure PN in accordance with ISO and including PN 25 where applicable. The overall service (design) coefficient shall not be less than that specified in EN ISO for the relevant material. For thermosetting materials the internal pressure strength of the pipe or fitting shall be tested in accordance with and shall be declared by the manufacturer as nominal pressure in accordance with EN 1796 or EN For multilayer pipes the internal pressure strength shall be tested and declared by the manufacturer in accordance with

10 Bestelformulier Stuur naar: NEN Standards Products & Services t.a.v. afdeling Klantenservice Antwoordnummer WB Delft NEN Standards Products & Services Postbus GB Delft Vlinderweg AX Delft Ja, ik bestel ex. NEN-EN 15014:2007 2e Ontw. en Kunststofleidingsystemen - Onderen bovengrondsystemen voor water en andere vloeistoffen onder druk - Prestatiekenmerken voor buizen, hulpstukken en hun verbindingen T (015) F (015) Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via Gratis nieuwsbrieven Wilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen, normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze nieuwsbrieven. Gegevens Bedrijf / Instelling T.a.v. O M O V Klantnummer NEN Uw ordernummer BTW nummer Postbus / Adres Postcode Plaats Telefoon Fax Factuuradres (indien dit afwijkt van bovenstaand adres) Postbus / Adres Postcode Plaats Datum Handtekening Retourneren Fax: klantenservice@nen.nl Post: NEN Standards Products & Services, t.a.v. afdeling Klantenservice Antwoordnummer 10214, 2600 WB Delft (geen postzegel nodig). Voorwaarden De prijzen zijn geldig tot 31 december 2018, tenzij anders aangegeven. Alle prijzen zijn excl. btw, verzend- en handelingskosten en onder voorbehoud bij o.m. ISO- en IEC-normen. Bestelt u via de normshop een pdf, dan betaalt u geen handeling en verzendkosten. Meer informatie: telefoon , dagelijks van 8.30 tot uur. Wijzigingen en typefouten in teksten en prijsinformatie voorbehouden. U kunt onze algemene voorwaarden terugvinden op: LEREN, WERKEN EN GROEIEN MET NEN preview